2024
Conception de dispositifs pour la séparation liquide-liquide continue et la technologie d'automatisation open source : des pousse-seringues VIT-FIT de LAMBDA ont été utilisés pour l'alimentation en fluide dans une configuration expérimentale microfluidique à base de gouttelettes pour la séparation de flux segmentés (phase dispersée : eau déionisée ; phase continue : polydiméthylsiloxane ( PDMS)).
Oldach, B., Chiang, Y. Y., Ben-Achour, L., Chen, T. J., & Kockmann, N. (2024). Performance of different microfluidic devices in continuous liquid-liquid separation. Journal of Flow Chemistry, 1-11.
https://doi.org/10.1007/s41981-024-00326-z
Pour étudier les interactions entre les segments du piston, la chemise de cylindre et le lubrifiant, un pousse-seringue VIT-FIT de LAMBDA a été utilisé pour l'alimentation en lubrifiant. Le système incliné et les pompes précises ont permis d'ajuster le débit très faible et continu d'huile chauffée à travers le contact tribologique.
Markut, T., Summer, F., Pusterhofer, M., & Grün, F. (2024). Emergence of Coated Piston Ring Scuffing Behavior on an Application-Oriented Tribological Model Test System. Lubricants, 12(6), 218.
https://doi.org/10.3390/lubricants12060218
Pour une étude expérimentale, un pousse-seringue VIT-FIT (HP) de LAMBDA a été utilisé pour le liquide et un microscope numérique à grande vitesse Meros pour enregistrer le mouvement des particules.
Ghadamgahi, S. M. E., Shahmardan, M. M., Nazari, M., Mansouri, H., & Hashemi, N. N. (2024). Numerical and experimental investigation of the deviation of microparticles inside the microchannel using the vortices caused by the ICEK phenomenon. Electrophoresis, 45(7-8), 720-734.
https://doi.org/10.1002/elps.202300151
Un pousse-seringue LAMBDA VIT-FIT a été utilisé pour introduire une solution de précurseur dans un atomiseur FSP à double fluide à un débit de 5 ml/min.
Deligiannakis, Y., Bletsa, E., Mouzourakis, E., Solakidou, M., & Adamska, K. (2024). Carbon-Coated TiO2 Nanoparticles for Noble-Metal-Free Photocatalytic H2 Production from H2O. ACS Applied Nano Materials.
https://doi.org/10.1021/acsanm.4c01150
Montage calorimétrique expérimental pour la mesure de réactions sensibles aux métaux : Deux pompes (une SyrDos de HiTec Zang et une LAMBDA VIT-FIT) sont utilisées pour introduire les solutions d'alimentation dans le calorimètre. Pour le calcul non biaisé de l'enthalpie de réaction par mole, une troisième pompe (LAMBDA VIT-FIT) est utilisée pour éteindre la réaction une fois la mesure calorimétrique terminée.
Soritz, S., Sommitsch, A., Irndorfer, S., Brouczek, D., Schwentenwein, M., Priestley, I. J. G., Iosub, A. V., Krieger, J. P., & Gruber-Woelfler, H. (2024). Thermokinetic analyses of metal-sensitive reactions in a ceramic flow calorimeter. Reaction Chemistry & Engineering.
https://doi.org/10.1039/D4RE00014E
Laboratoire de conception d'équipements : Modification pour étendre la capacité du pousse-seringue de laboratoire LAMBDA VIT-FIT à deux seringues (HENKE-JECT® Luer Lock 50 mL)
Höving, S., Ronnewinkel, P., & Kockmann, N. (2024). From Batch to Continuous Small-Scale Production of Particles: Mixer Design Methodology for Robust Operation. Crystals, 14(5), 398.
https://doi.org/10.3390/cryst14050398
Figure: https://pub.mdpi-res.com/crystals/crystals-14-00398/article_deploy/html/images/crystals-14-00398-g0A1.png (2024 April 30)
Le pousse-seringue LAMBDA VIT-FIT / VIT-FIT HP avec une seringue Hamilton (diamètre 0.82 mm, volume 25 µl) est utilisé pour injecter un fluide contenant des particules de levure dans un microcanal.
Aghdasi, M., Nazari, M., Holari, S. Y., & Hashemi, N. N. (2024). Designing a new microchannel to collect microparticles using dielectrophoretic forces: Numerical and experimental investigation. Journal of Electrostatics, 127, 103879.
https://doi.org/10.1016/j.elstat.2023.103879
2023
La solution est injectée dans le microcanal à l'aide d'un pousse-seringue LAMBDA VIT-FIT HP avec un débit de 0.0353 µl/s.
Aghdasi, M., Nazari, M., & Yonesi, S. (2023). A novel micro-device for simultaneous separation-trapping and double-trapping of particles by using dielectrophoresis: numerical and experimental study. Journal of Micromechanics and Microengineering, 33(10), 105015.
https://doi.org/10.1088/1361-6439/acef32
Ingénierie des microprocessus pour applications microfluidiques avec carte microcontrôleur pour l'accès et le contrôle des actionneurs du système : a) pousse-seringues avec interface RS-232 ; b) vannes (situées entre les pousse-seringues et les entrées des dispositifs microfluidiques). Les pousse-seringues LAMBDA VIT-FIT délivraient les liquides non miscibles avec des débits réglables individuellement (0.1 - 10 ml/min) pour différents modèles d'écoulement liquide-liquide, tandis que la commutation télécommandée des positions des vannes alimentait les géométries souhaitées en fluide.
Oldach, B., Höving, S., Boettcher, K. E., & Kockmann, N. (2023, March). Ultra-concurrent remote laboratory for microfluidic applications. In International Conference on Remote Engineering and Virtual Instrumentation (pp. 463-476). Cham: Springer Nature Switzerland.
https://doi.org/10.1007/978-3-031-42467-0_43
Le pousse-seringue programmable LAMBDA VIT-FIT avec une seringue de 120 ml a été utilisé pour délivrer une solution (volume total 800 ml) : Débit de pompe 1.2 ml/s ; temps de pompage 2 minutes (1 minute pour remplir et 1 minute pour vider la seringue).
Svara, D., Filipova, B., Jelinek, P., Mikes, P., Kluk, A., & Soós, M. (2023). The impact of polymer mixture composition on the properties of electrospun membranes for drug delivery applications. International Journal of Pharmaceutics, 647, 123548.
https://doi.org/10.1016/j.ijpharm.2023.123548
Une impulsion d'un traceur inerte de bromure de potassium a été introduite à l'entrée (c0,KBr = 0.303 mol/m3 ; Q = 5 ml/min ; total V = 100 ml) avec un pousse seringue LAMBDA VIT-FIT.
Markale, I., Carrel, M., Kurz, D. L., Morales, V. L., Holzner, M. & Jiménez-Martínez, J. (2023). Internal Biofilm Heterogeneities Enhance Solute Mixing and Chemical Reactions in Porous Media. Environmental Science & Technology 2023 57 (21), 8065-8074
https://doi.org/10.1021/acs.est.2c09082
Pousse-seringue LAMBDA VIT-FIT pour l'injection d'eau à des débits de 2.1 ml/h, 4.3 ml/h et 6.4 ml/h (électrovanne pilotée par un temporisateur dans la ligne) dans le cadre d'un montage expérimental microfluidique : injection WAG (Water Alternating Gas) pour le déplacement d'huile dans des milieux poreux à l'aide de quatre fluides différents, notamment du gaz (N2), del'eau, le WAG et la coinjection de liquide et de gaz.
Jafarian, K., Kayhani, M.H., Nazari, M., Ghorbanbakhsh, B. & Shokri, N. (2023). WAG injection in porous media: A microfluidic analysis. Chemical Engineering Research and Design, Volume 193, 2023, Pages 649-659, ISSN 0263-8762,
https://doi.org/10.1016/j.cherd.2023.03.035
Alimentation de réactifs dans un microréacteur à l’aide de deux pousse-seringues VIT-FIT de LAMBDA (connectées au système d'automatisation de laboratoire LabManager et au logiciel d'automatisation LabVision)
Frede, T.A., Weber, C., Brockhoff, T., Christ, T., Ludwig, D. & Kockmann, N. (2023). Data Management of Microscale Reaction Calorimeter Using a Modular Open-Source IoT-Platform. Processes 2023, 11, 279.
https://doi.org/10.3390/pr11010279
Un pousse seringue LAMBDA VIT-FIT a été utilisé pour réaliser un l'écoulement de fluide à travers le dispositif microfluidique diélectrophorétique.
Valijam, S., Nilsson , D.P.G., Malyshev, D., Öberg, R., Salehi, A. & Andersson, M. (2023). Fabricating a dielectrophoretic microfluidic device using 3D-printed moulds and silver conductive paint.
https://doi.org/10.48550/arXiv.2302.10690
Un pousse seringue LAMBDA VIT-FIT a été utilisée pour remplir l'intestin grêle porcin avec de l'eau DI (1 ml/min).
Cipolato, O., Dosnon, L., Rosendorf, J., Sarcevic, S., Bondi, A., Liska, V., Schlegel, A.A. & Herrmann I.K. (2023). Nanothermometry-enabled intelligent laser tissue soldering. bioRxiv 2023.03.03.530945;
https://doi.org/10.1101/2023.03.03.530945
2022
Des pousse seringue LAMBDA VIT-FIT ont été utilisés pour alimenter des réactifs préchauffés individuellement à partir de flacons de stockage via des tuyaux FEP à température contrôlée dans un microréacteur.
Frede, T.A., Greive, M. & Kockmann, N. (2022). Measuring Kinetics in Flow Using Isoperibolic Flow Calorimetry. Reactions 2022, 3, 525–536.
https://doi.org/10.3390/reactions3040035
Le pousse-seringue LAMBDA VIT-FIT a été utilisée pour injecter un fluide sans bulles à l’entrée d’un micro canal via des tubes capillaires en silicone d'un diamètre de 1.0 mm.
Tavari, T., Meamardoost, S., Sepehry, N., Sepehry, N., Akbarzadeh, P., Nazari, M., Hashemi, N.N. & Nazari, M. (2022). Effects of 3D electrodes arrangement in a novel AC electroosmotic micropump: Numerical modeling and experimental validation. Electrophoresis. 2022; 1– 12.
https://doi.org/10.1002/elps.20220021
2021
Le pousse-seringue LAMBDA VIT-FIT injecte le mélange de monomères MMA/EGDMA (80 % / 20 %) dans le réacteur de polymérisation à un débit de 2.5 mL/min.
Wilson, J. F., Zahradnik, B., Šrom, O., Jaquet, B., Hassouna, F., Hrdlicka, Z., Kosek, J., & Šoóš, M. (2021). Study of the shear-thinning effect between polymer nanoparticle surfaces during shear-induced aggregation. Industrial & Engineering Chemistry Research, 60(29), 10654-10665.
https://doi.org/10.1021/acs.iecr.1c00232
200 µL de plasma de truite arc-en-ciel dilué et dopé ont été pompés à travers un capillaire revêtu de PDMS avec des débits définis (24 – 0.2 ml/h) à l'aide d'un pousse-seringue LAMBDA VIT-FIT.
Krause, S. & Goss, K. U. (2021). Could chemical exposure and bioconcentration in fish be affected by slow binding kinetics in blood? Environmental Science: Processes & Impacts, 2021, Advance Article;
https://doi.org/10.1039/d1em00056j
Mélange microfluidique à base de feuille de polyimide : pousse-seringues LAMBDA VIT-FIT avec seringues de 50 mL (Henke-Ject) pour aliments préchauffés à 25 °C.
Bobers, J., Forys, E., Oldach, B., & Kockmann, N. (2021). Application of Polyimide‐based Microfluidic Devices on Acid‐catalyzed Hydrolysis of Dimethoxypropane. Chemie Ingenieur Technik, 93(5), 796-801.
https://doi.org/10.1002/cite.202000224
Un pousse-seringues LAMBDA VIT-FIT pompe de l’alcool isoamylique (> 98.5 %) à des débits volumétriques continus (10, 20, 30, 40, 80, 227.9 μL/min) à l’aide d’une seringue de 50 ml dans un bain-marie isolé thermiquement équipé d’un microréacteur.
Lee, C. S., Vorwerk, C., Azudin, N. Y., Ahmad, N. A., & Abd Shukor, S. R. (2021). Kinetics modelling of uncatalyzed esterification of acetic anhydride with isoamyl alcohol in a microreactor system. Journal of Environmental Chemical Engineering, 9(3), 105219.
https://doi.org/10.1016/j.jece.2021.105219
Un pousse-seringue LAMBDA VIT-FIT est équipé d'une seringue en acier inoxydable de 50 mL remplie d'une solution mère 10 mM d'acide coumarique (substrat). Les sorties de deux pompes sont reliées à un mélangeur statique, afin de fournir un flux d'alimentation avec une concentration uniforme avant qu'il n'atteigne l'entrée de la colonne.
Valotta, A., Maier, M. C., Soritz, S., Pauritsch, M., Koenig, M., Brouczek, D., Schwentenwein, M. & Gruber-Woelfler, H. (2021). 3D printed ceramics as solid supports for enzyme immobilization: an automated DoE approach for applications in continuous flow. Journal of Flow Chemistry, 11(3), 675-689.
https://doi.org/10.1007/s41981-021-00163-4
De l'eau pure est pompée à l'aide d'un BlueShadow et de l'eau pure enrichie en iodure de potassium (KI) est pompée par un LAMBDA VIT-FIT dans un tube rotatif enroulé en hélice (HCT) qui est monté dans le scanner de tomodensitométrie (Skyscan 1275).
Schuler, J., Herath, J., & Kockmann, N. (2021). 3D investigations of microscale mixing in helically coiled capillaries. Journal of Flow Chemistry, 11, 217-222.
https://doi.org/10.1007/s41981-021-00161-6
2017
Débits constants et reproductibles de 26 ± 2 nL/s créés par un pousse-seringue microfluidique LAMBDA VIT-FIT équipé d'une pipette de 10 μl
Zhang, H., Stangner, T., Wiklund, K., Rodriguez, A., & Andersson, M. (2017). UmUTracker: A versatile MATLAB program for automated particle tracking of 2D light microscopy or 3D digital holography data. Computer Physics Communications, 219, 390-399.
https://doi.org/10.1016/j.cpc.2017.05.029
2016
Pour la synthèse des nanopoudres, une solution précurseur (dans l'éthanol) a été introduite par une buse FASP refroidie à l'eau à l'aide d'un pousse-seringue LAMBDA VIT-FIT à débit constant et dispersée avec 3 à 6 L/min d'O2 tout en maintenant une chute de pression de 1.6 à 1.8 bar au niveau de la buse.
Posavec, L., Knijnenburg, J. T., Hilty, F. M., Krumeich, F., Pratsinis, S. E., & Zimmermann, M. B. (2016). Dissolution and storage stability of nanostructured calcium carbonates and phosphates for nutrition. Journal of Nanoparticle Research, 18, 1-13.
https://doi.org/10.1007/s11051-016-3608-6
Pousse-seringue LAMBDA VIT-FIT utilisé pour pomper la solution précurseur (dans A) toluène, B) éther monobutylique de diéthylèneglycol et anhydride acétique ou C) toluène, 2-éthylhexanoate et acétonitrile (3:1:1)) à raison de 5 ml/min dans la buse du réacteur à flamme
Koirala, R., Buechel, R., Pratsinis, S. E., & Baiker, A. (2016). Silica is preferred over various single and mixed oxides as support for CO2-assisted cobalt-catalyzed oxidative dehydrogenation of ethane. Applied Catalysis A: General, 527, 96-108.
https://doi.org/10.1016/j.apcata.2016.08.032
Pousse-seringue LAMBDA VIT-FIT pour alimenter d’une solution de précurseur (acétylacétonate de fer(III) dans le xylène et l'acétonitrile (rapport volumique 3:1) avec une concentration totale en fer de 0.34 M) à 5 ml/min pour la synthèse de nanoparticules magnétiques
Teleki, A., Haufe, F. L., Hirt, A. M., Pratsinis, S. E., & Sotiriou, G. A. (2016). Highly scalable production of uniformly-coated superparamagnetic nanoparticles for triggered drug release from alginate hydrogels. RSC advances, 6(26), 21503-21510.
https://doi.org/10.1039/C6RA03115C
Pousse-seringue LAMBDA VIT-FIT pour le séchage par pulvérisation d'une solution aqueuse contenant de l'allergène HDM et du lactose pour générer un aérosol
Lüer, K., Biller, H., Casper, A., Windt, H., Müller, M., Badorrek, P., Haefner, D., Framke, T., Koch, A., Ziehr, H., Krug, N., Koch, W., & Hohlfeld, J. M. (2016). Safety, efficacy and repeatability of a novel house dust mite allergen challenge technique in the Fraunhofer allergen challenge chamber. Allergy, 71(12), 1693-1700.
https://doi.org/10.1111/all.12947
Mesure de la pression d'éclatement : La canule a été fixée sur un robinet à trois voies relié à un appareil de mesure de pression (GMH 5130) doté de capteurs de pression (MSD 1 BRE, plage 0 – 1 bar, GHM Messtechnik) et d'une pompe à perfusion (LAMBDA VIT-FIT), qui perfusait une solution saline à un débit constant de 200 ml/min.
Holmer, C., Winter, H., Nagel, A., Jaenicke, A., Lauster, R., Kraft, M., Buhr, H. J., Ritz, J.-P., & Zickerow, M. (2016). Bipolar radio-frequency-induced thermofusion of intestinal tissue–In vivo evaluation of a new fusion technique in an experimental study. International Journal of Hyperthermia, 32(5), 583-586.
https://doi.org/10.3109/02656736.2016.1168872
2015
LAMBDA VIT-FIT syringe pump used to deliver the liquid feed solutions at a Qlf of 1 ml/min to the nozzles of the spray dryer
Schäfer, J. (2015). Spray-Drying of Enzymes on the Bench-Top Scale with lengthened Chamber Retention Time (Doctoral dissertation, Erlangen, Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), Diss., 2015).
URI: https://open.fau.de/handle/openfau/5935 (2024 April 22)
Cyclic bending tests of Ag–PMMA nanocomposite films were conducted by programmable motor of LAMBDA VIT-FIT syringe pump
Blattmann, C. O., Sotiriou, G. A., & Pratsinis, S. E. (2015). Rapid synthesis of flexible conductive polymer nanocomposite films. Nanotechnology, 26(12), 125601.
https://doi.org/10.1088/0957-4484/26/12/125601
Programmable LAMBDA VIT-FIT syringe pump was used to add the methyl methacrylate (MMA) at a flow rate of 0.1 g/min to synthesis the poly(methyl methacrylate) (PMMA) nanoparticles.
Villiger, T. K., Morbidelli, M., & Soos, M. (2015). Experimental determination of maximum effective hydrodynamic stress in multiphase flow using shear sensitive aggregates. AIChE Journal, 61(5), 1735-1744.
https://doi.org/10.1002/aic.14753
Precursor solutions (gallium acetylacetonate and titanium isopropoxide dissolved in xylene) were injected at 5 ml/min by LAMBDA VIT-FIT syringe pump through the FSP nozzle to investigate the catalytic behaviour of TiO2 supported Ga2O3 in ODHE.
Koirala, R., Buechel, R., Krumeich, F., Pratsinis, S. E., & Baiker, A. (2015). Oxidative dehydrogenation of ethane with CO2 over flame-made Ga-loaded TiO2. ACS Catalysis, 5(2), 690-702.
https://doi.org/10.1021/cs500685d
2014
Syringe pump LAMBDA VIT-FIT connected to a diffuser (wood or ceramic) with selected speed of 0.8 mm/min, used for homogeneous dispersion of bubbles
Souzy, N. (2014). Experimental study and improvement of mass transfer in vertical bubble columns (Doctoral dissertation, Lyon 1).
https://theses.hal.science/tel-01127296 (2024 April 22)
To prepare the macroporous microparticles, aggregation was induced under shear stress under defined stirring speed by adding equal volumes of saline solutions during two successive gradients (2 × 10 ml) using a programmable syringe pump (LAMBDA VIT-FIT) at a defined flow rate.
Lamprou, A., Köse, I., Peña Aguirre, Z., Storti, G., Morbidelli, M., & Soos, M. (2014). Macroporous polymer particles via reactive gelation under shear: effect of primary particle properties and operating parameters. Langmuir, 30(46), 13970-13978.
https://doi.org/10.1021/la502153j
Flow rate of coffee extract held constant at 1 ml/min by programmable syringe pump LAMBDA VIT-FIT to study the deposition kinetics of an industrial coffee extract over a wide range of temperatures
Kroslak, M., Morbidelli, M., & Sefcik, J. (2014). Effects of temperature and concentration on mechanism and kinetics of thermally induced deposition from coffee extracts. Chemical Papers, 68(12), 1755-1766.
https://doi.org/10.2478/s11696-014-0628-5
Flame spray pyrolysis (FSP): LAMBDA VIT-FIT syringe pump was used to inject (5 ml/min) and disperse the precursor solution into fine droplets by co-flowing 5 L/min of O2 maintaining a pressure drop of 2 bar at the nozzle tip.
Koirala, R., Büchel, R., Pratsinis, S. E., & Baiker, A. (2014). Oxidative coupling of methane on flame-made Mn-Na2WO4/SiO2: Influence of catalyst composition and reaction conditions. Applied Catalysis A: General, 484, 97-107.
https://doi.org/10.1016/j.apcata.2014.07.013
Two monomeric mixtures were fed at a rate of 0.056 ml/min for latex preparation followed by induced aggregation under shear by addition of gradient salts at a rate of 4.23 ml/min using LAMBDA VIT-FIT programmable syringe pumps for the synthesis of macroporous copolymer resins
Alexandros, L., Itır, K., Giuseppe, S., Massimo, M., & Miroslav, S. (2014). Synthesis of Macroporous Polymer Particles Using Reactive Gelation under Shear. Langmuir 2014 30 (23), 6946-6953
https://doi.org/10.1021/la5000793
Programmable syringe pump (LAMBDA VIT-FIT) filled with SF6 used for continuous infusion of microbubbles (MBs) into rabbits
Lukáč, R. (2014). Micro and Nanoparticles as Drug Carriers: Surface-Modified Microbubbles Used as Ultrasound Contrast Agents and Drug Carriers (Doctoral dissertation, Masarykova univerzita, Přírodovědecká fakulta).
http://is.muni.cz/th/271136/prif_d/Robert_Lukac.pdf (2024 April 22)
The cytochrome c (cyt c) solution was injected into the ternary lipid membranes of the flow chamber system using a LAMBDA VIT-FIT programmable syringe pump at a sufficiently low speed that the system was not disturbed by liquid flow to study the phase behavior.
Pataraia, S., Liu, Y., Lipowsky, R., & Dimova, R. (2014). Effect of cytochrome c on the phase behavior of charged multicomponent lipid membranes. Biochimica et Biophysica Acta (BBA)-Biomembranes, 1838(8), 2036-2045.
https://doi.org/10.1016/j.bbamem.2014.04.019
Monomer addition was controlled by a programmable syringe pump LAMBDA VIT-FIT
Codari, F., Moscatelli, D., Furlan, M., Lattuada, M., Morbidelli, M., & Soos, M. (2014). Synthesis of Hetero-nanoclusters: The Case of Polymer–Magnetite Systems. Langmuir, 30(8), 2266-2273.
https://doi.org/10.1021/la5001039
"A perfusor (LAMBDA VIT-FIT polyvalent syringe infusion pump) controlled syringe injected the MCh solution via a dispersion nozzle (Fraunhofer ITEM) operated with pressurized air into a custom-made evaporation chamber (140 mm diameter and 350 mm length) that was warmed up to 313.2 K."
Curths, C., Wichmann, J., Dunker, S., Windt, H., Hoymann, H. G., Lauenstein, H. D., Hohlfeld, J., Becker, T., Kaup, F. J., Braun, A., & Knauf, S. (2014). Airway hyper-responsiveness in lipopolysaccharide-challenged common marmosets (Callithrix jacchus). Clinical science, 126(2), 155-162.
https://doi.org/10.1042/CS20130101
2013
Water injection at a flow rate of 200 μl/min with a LAMBDA VIT-FIT programmable syringe pump
Aüllo, T. (2013). Atténuation naturelle potentielle de BTEX en aquifère de stockage de gaz (Doctoral dissertation, Pau).
https://theses.fr/2013PAUU3018 (2024 April 23)
Delivering of the precursor solution to the flame by the LAMBDA VIT-FIT syringe pump at a rate of 5 ml/min
Wallace, R., Brown, A. P., Brydson, R., Wegner, K., & Milne, S. J. (2013). Synthesis of ZnO nanoparticles by flame spray pyrolysis and characterisation protocol. Journal of Materials Science, 48, 6393-6403.
https://doi.org/10.1007/s10853-013-7439-x
Maintaining of fluid circulation in the inverted microscope by LAMBDA VIT-FIT syringe pump
Mbaye, S., Séchet, P., Pignon, F., & Martins, J. M. F. (2013). Influence of hydrodynamics on the growth kinetics of glass-adhering Pseudomonas putida cells through a parallel plate flow chamber. Biomicrofluidics, 7(5).
https://doi.org/10.1063/1.4821244
Construction of a microfuidic adhesion cell: Feeding of fluid to the flow cell through Tygon hoses connected to a syringe pump LAMBDA VIT-FIT
Tokárová, V., Pittermannová, A., Král, V., Řezáčová, P., & Štěpánek, F. (2013). Feasibility and constraints of particle targeting using the antigen–antibody interaction. Nanoscale, 5(23), 11490-11498.
https://doi.org/10.1039/C3NR04340A
Mounting of the initiator solution by two programmable single syringe pumps LAMBDA VIT-FIT
Diederich, V. E., Studer, P., Kern, A., Lattuada, M., Storti, G., Sharma, R. I., Snedeker, J. G., & Morbidelli, M. (2013). Bioactive polyacrylamide hydrogels with gradients in mechanical stiffness. Biotechnology and bioengineering, 110(5), 1508-1519.
https://doi.org/10.1002/bit.24810
Continuous infusion of microbubbles with the LAMBDA VIT-FIT programmable syringe pump
Kauerová, Z., Lukáč, R., Kohout, P., Mašek, J., Koudelka, Š., Plocková, J., Vašíčková , M., Vlašín, M., & Turánek, J. (2013). A prototype ‘Infucon’device for continuous infusion of microbubbles in vivo. International journal of pharmaceutics, 441(1-2), 92-98.
https://doi.org/10.1016/j.ijpharm.2012.12.026
Acid dosage in the experimental setup: Using a LAMBDA VIT-FIT syringe pump, concentrated sulfuric or perchloric acid was injected via a needle (outlet diameter 500 mm) near the impeller of the stirred tank reactor
Kölbl, A., Desplantes, V., Grundemann, L., & Scholl, S. (2013). Kinetic investigation of the Dushman reaction at concentrations relevant to mixing studies in stirred tank reactors. Chemical engineering science, 93, 47-54.
https://doi.org/10.1016/j.ces.2013.01.067
Aerosol Science and Technology: LAMBDA VIT-FIT HP injection system for production of aerosol with Bacillus thuringiensis spores
Roux, J. M., Kaspari, O., Heinrich, R., Hanschmann, N., & Grunow, R. (2013). Investigation of a new electrostatic sampler for concentrating biological and non-biological aerosol particles. Aerosol Science and Technology, 47(5), 463-471.
https://doi.org/10.1080/02786826.2013.763896
2012
Using of the LAMBDA VIT-FIT syringe pump during intravitreal injection of rotenone (5 and 15 mM in DMSO) or DMSO (vehicle)
Heitz, F. D., Erb, M., Anklin, C., Robay, D., Pernet, V., & Gueven, N. (2012). Idebenone Protects against Retinal Damage and Loss of Vision in a Mouse Model of Leber's Hereditary Optic Neuropathy. PLoS ONE, 7(9), e45182-e45182.
https://doi.org/10.1371/journal.pone.0045182
"The precursor solution was fed at 2−6 mL/min through the FASP or FSP spray nozzles by a LAMBDA VIT-FIT syringe pump and atomized by coflowing 6 L/min of oxygen at 1.5 bar pressure drop."
Rudin, T., & Pratsinis, S. E. (2012). Homogeneous iron phosphate nanoparticles by combustion of sprays. Industrial & engineering chemistry research, 51(23), 7891-7900.
https://doi.org/10.1021/ie202736s
Comparison of surgical scissors on a pig model: Saline infusion kept constant by LAMBDA VIT-FIT syringe-pump
Seehofer, D., Mogl, M., Boas-Knoop, S., Unger, J., Schirmeier, A., Chopra, S., & Eurich, D. (2012). Safety and efficacy of new integrated bipolar and ultrasonic scissors compared to conventional laparoscopic 5-mm sealing and cutting instruments. Surgical endoscopy, 26, 2541-2549.
https://doi.org/10.1007/s00464-012-2229-0
Experimental set-up with custom-designed adhesion cell and a LAMBDA VIT-FIT syringe pump with heated fluid in the syringe to control the volumetric flow rate.
Tokárová, V., Pittermannová, A., Čech, J., Ulbrich, P., & Štěpánek, F. (2012). Thermo-responsive adhesion properties of composite hydrogel microcapsules. Soft matter, 8(4), 1087-1095.
https://doi.org/10.1039/c1sm06783d
2011
Slow injection of CdCl2 solution into the chamber containing Na2S-loaded GUVs without detaching the vesicles from the substrate, done by polyvalent LAMBDA VIT-FIT syringe pump (at a speed of 1 ml/min).
Yang, P., & Dimova, R. (2011). Nanoparticle synthesis in vesicle microreactors. In Biomimetic based applications (pp. 523-552). InTech.
https://pure.mpg.de/rest/items/item_1925392/component/file_3274796/content (2024 April 22)
The syringe pump was used to provide a constant flow rate of liquid through the nozzle to analyze the breakage and restructuring of colloidal aggregates in dilute conditions under shear.
Harshe, Y. M., Lattuada, M., & Soos, M. (2011). Experimental and modeling study of breakage and restructuring of open and dense colloidal aggregates. Langmuir, 27(10), 5739-5752.
https://doi.org/10.1021/la1046589
Pumping of sample solution at a speed of 8 μl/min through an insulating Teflon tubing to the steel spraying capillary with a LAMBDA VIT-FIT syringe pump
Büttiker, R., Ebert, J., Hinderling, C., & Adlhart, C. (2011). Membranes for specific adsorption: immobilizing molecularly imprinted polymer microspheres using electrospun nanofibers. Chimia, 65(3), 182-186.
https://doi.org/10.2533/chimia.2011.182
Dosing of fluids with LAMBDA VIT-FIT syringe pumps for reliably assessment of protein structures under various conditions
Prim, D., Crelier, S., & Segura, J. M. (2011). Coupling of a Microfluidic Mixer to a Fourier-transform Infrared Spectrometer for Protein-Conformation Studies. FH–HES. Chimia, 65(10), 815-815.
https://doi.org/10.2533/chimia.2011.815
LAMBDA VIT-FIT syringe pump as the final control element in order to manipulate the flow rate of the injected strong base into the microreactor
Abd Shukor, S. R., Barzin, R., & Ahmad, A. L. (2011). Computer-Based Control for Chemical Systems Using LabVIEW® in Conjunction with MATLAB®. Practical Applications and Solutions Using LabVIEW™ Software, 363.
https://doi.org/10.5772/19414
LAMBDA VIT-FIT infusion pump for inflated colon samples
Holmer, C., Winter, H., Kröger, M., Nagel, A., Jaenicke, A., Lauster, R., Kraft, M., Buhr, H. J., & Ritz, J. P. (2011). Bipolar radiofrequency-induced thermofusion of intestinal anastomoses—feasibility of a new anastomosis technique in porcine and rat colon. Langenbeck's archives of surgery, 396, 529-533.
https://doi.org/10.1007/s00423-011-0756-0
The solution was fed with a LAMBDA VIT-FIT syringe pump at 2 ml/min through the spray nozzle (capillary inner/outer diameter 0.41/0.72 mm) and by co-flowing 6 L/min oxygen through a surrounding annulus (0.97 mm o.d.) at a pressure drop of 1.5 bar.
Rudin, T., Wegner, K., & Pratsinis, S. E. (2011). Uniform nanoparticles by flame-assisted spray pyrolysis (FASP) of low cost precursors. Journal of Nanoparticle Research, 13, 2715-2725.
https://doi.org/10.1007/s11051-010-0206-x
2010
LAMBDA VIT-FIT syringe pump was used to investigate the breakup of dense aggregates in an extensional flow through a contracting nozzle
Soos, M., Ehrl, L., Bäbler, M. U., & Morbidelli, M. (2010). Aggregate breakup in a contracting nozzle. Langmuir, 26(1), 10-18.
https://doi.org/10.1021/la903982n
Using a LAMBDA VIT-FIT syringe pump as the final control element in order to manipulate the flow rate of sodium hydroxide into the SSIMM micro-reactor
Barzin, R., Abd Shukor, S. R., & Ahmad, A. L. (2010). New spectrophotometric measurement method for process control of miniaturized intensified systems. Sensors and Actuators B: Chemical, 146(1), 403-409.
https://doi.org/10.1016/j.snb.2010.01.072
LAMBDA VIT-FIT syringe pump with a driving force of 300 N is used with the advantage that different syringes run with this type and the driving velocity can be chosen in 0 and 999 increments. The characteristic functions of four typical types of syringes (2, 5, 10 and 20 ml) were recorded
Bauer, M., Heusel, G., Mangold, S., & Bertagnolli, H. (2010). Spectroscopic set-up for simultaneous UV-Vis/(Q) EXAFS in situ and in operando studies of homogeneous reactions under laboratory conditions. Journal of Synchrotron Radiation, 17(2), 273-279.
https://doi.org/10.1107/S0909049509054910
Injection of poly-L-lactide by computerized syringe pump LAMBDA VIT-FIT at a controlled rate
François, S., Sarra‐Bournet, C., Jaffre, A., Chakfé, N., Durand, B., & Laroche, G. (2010). Characterization of an air‐spun poly (l‐lactic acid) nanofiber mesh. Journal of Biomedical Materials Research Part B: Applied Biomaterials, 93(2), 531-543.
https://doi.org/10.1002/jbm.b.31612
Usage of LAMBDA VIT-FIT syringe pump to achieve a good reproducibility for the salt injection and off-line sampling
Ehrl, L., Soos, M., Wu, H., & Morbidelli, M. (2010). Effect of flow field heterogeneity in coagulators on aggregate size and structure. AIChE journal, 56(10), 2573-2587.
https://doi.org/10.1002/aic.12179
The gas samples were introduced into the measuring system using a gas-tight syringe (Fortuna-optima® 100 ml) and a constant volume flow rate of 40 ml/min (syringe pump LAMBDA VIT-FIT).
Peitzsch, M., Kremer, D., & Kersten, M. (2010). Mikrobiologische Volatilisierung von anorganischem Selen aus Deponiesickerwässern bei umweltrelevanten Konzentrationen. Umweltwissenschaften und Schadstoff-Forschung, 22(2), 107-115.
https://doi.org/10.1007/s12302-010-0113-x
2009
Ajout de monomère dans un réacteur à un débit de 4.5 ml/h par un pousse-seringue programmable LAMBDA VIT-FIT
GuarnaschelliI, M. (2009). Sviluppo di nanoparrticelle polimeriche per il passaggio della barriera emato-encefalica. Farmaceutico Tecnologico Applicativo, Politecnico di Milano, Italy
https://www.politesi.polimi.it/handle/10589/608 (2024 April 23)
Une solution de PLLA dans une seringue en verre a été injectée à un débit contrôlé avec un pousse-seringue informatisé LAMBDA VIT-FIT.
François, S. (2009). Optimisation de la structure textile des prothèses vasculaires pour un développement en monocouche des cellules endothéliales (Doctoral dissertation, Université de Haute Alsace-Mulhouse; Université Laval (Québec, Canada)).
https://theses.hal.science/tel-00590477 (2024 April 23)
Utilisation d'un pousse-seringue LAMBDA VIT-FIT pour l'injection de sel afin d'obtenir une bonne reproductibilité de la cinétique d'agrégation initiale
Ehrl, L., Soos, M., Morbidelli, M., & Bäbler, M. U. (2009). Dependence of initial cluster aggregation kinetics on shear rate for particles of different sizes under turbulence. AIChE journal, 55(12), 3076-3087.
https://doi.org/10.1002/aic.11923
Échange lent de solution dans des vésicules avec le pousse-seringue programmable LAMBDA VIT-FIT
Yang, P., Lipowsky, R., & Dimova, R. (2009). Nanoparticle formation in giant vesicles: synthesis in biomimetic compartments. small, 5(18), 2033-2037.
https://doi.org/10.1002/smll.200900560
Réacteur alimenté en continu avec le pousse-seringue programmable LAMBDA VIT-FIT
Gonzalez-Olmos, R., Roland, U., Toufar, H., Kopinke, F. D., & Georgi, A. (2009). Fe-zeolites as catalysts for chemical oxidation of MTBE in water with H2O2. Applied Catalysis B: Environmental, 89(3-4), 356-364.
https://doi.org/10.1016/j.apcatb.2008.12.014
2008
L'installation utilisée comprenait deux seringues (Becton, Dickinson and Company, USA) reliées par un capillaire. Le débit a été contrôlé à l'aide d'un pousse-seringue programmable LAMBDA VIT-FIT.
Tanzeglock, T. (2008). A novel lobed Taylor-Couette bioreactor for the cultivation of shear sensitive cells and tissues (Doctoral dissertation, ETH Zurich).
https://doi.org/10.3929/ethz-a-005773994
https://www.research-collection.ethz.ch/bitstream/handle/20.500.11850/151055/eth-41563-02.pdf (2024 April 23)
Cryopiégeage à un débit de 40 ml/min avec un pousse-seringue programmable LAMBDA VIT-FIT
Peitzsch, M. (2008). Speziation mikrobiologisch alkylierter, leichtflüchtiger Selenverbindungen in Abhängigkeit der geochemischen Verfügbarkeit des Selens (Doctoral dissertation, Universitätsbibliothek Johannes Gutenberg-Universität Mainz).
https://doi.org/10.25358/openscience-3235
Utilisation du pousse-seringue LAMBDA VIT-FIT pour l'injection de sel afin d'obtenir une bonne reproductibilité de la cinétique d'agrégation initiale
Soos, M., Moussa, A. S., Ehrl, L., Sefcik, J., Wu, H., & Morbidelli, M. (2008). Effect of shear rate on aggregate size and morphology investigated under turbulent conditions in stirred tank. Journal of colloid and interface science, 319(2), 577-589.
https://doi.org/10.1016/j.jcis.2007.12.005
Cinétique d’agrégation initiale en appliquant la vitesse maximale
Soos, M., Moussa, A. S., Ehrl, L., Sefcik, J., Wu, H., & Morbidelli, M. (2008). Dynamic response studies on aggregation and breakage dynamics of colloidal dispersions in stirred tanks. Journal of dispersion science and technology, 29(4), 605-610.
https://doi.org/10.1080/01932690701729633
Utilisation du pousse-seringue LAMBDA VIT-FIT pour l'injection de sel afin d'obtenir une bonne reproductibilité de la cinétique d'agrégation initiale en appliquant la vitesse maximale
Ehrl, L., Soos, M., & Morbidelli, M. (2008). Dependence of aggregate strength, structure, and light scattering properties on primary particle size under turbulent conditions in stirred tank. Langmuir, 24(7), 3070-3081.
https://doi.org/10.1021/la7032302
Injection de coagulant et prélèvement d'échantillons à l'aide du pousse seringue LAMBDA VIT-FIT
Moussa, A. S. (2008). Experimental investigation and population balance modeling of aggregation and breakage of polymer colloids in turbulent flow (Doctoral dissertation, ETH Zurich).
https://doi.org/10.3929/ethz-a-005564260
2007
Réalisation de l'injection de sel avec un pousse-seringue LAMBDA VIT-FIT pour obtenir une bonne reproductibilité de la cinétique d'agrégation initiale en appliquant la vitesse maximale
Moussa, A. S., Soos, M., Sefcik, J., & Morbidelli, M. (2007). Effect of solid volume fraction on aggregation and breakage in colloidal suspensions in batch and continuous stirred tanks. Langmuir, 23(4), 1664-1673.
https://doi.org/10.1021/la062138m
Dépose précise d'une gouttelette suspendue sur une lamelle avec un pousse-seringue de laboratoire LAMBDA VIT-FIT
Kim, Y., Hong, S., Lee, S. H., Lee, K., Yun, S., Kang, Y., Paek, K.-K., Ju, B.-K., & Kim, B. (2007). Novel platform for minimizing cell loss on separation process: Droplet-based magnetically activated cell separator. Review of Scientific Instruments, 78(7).
https://doi.org/10.1063/1.2751414
Pousse-seringue de laboratoire LAMBDA VIT-FIT : Injection d’une suspension cellulaire à un débit de 4 μl/min à travers une tubulure en Téflon
Kim, S. K., Kim, J. H., Kim, K. P., & Chung, T. D. (2007, January). Low voltage DC electroporation chip with polyelectrolyte salt bridges. In 2007 IEEE 20th International Conference on Micro Electro Mechanical Systems (MEMS) (pp. 465-468). IEEE.
https://doi.org/10.1109/MEMSYS.2007.4433072
Le débit a été maintenu constant grâce au pousse-seringue programmable LAMBDA VIT-FIT
Kroslak, M., Sefcik, J., & Morbidelli, M. (2007). Effects of temperature, pH, and salt concentration on β-lactoglobulin deposition kinetics studied by optical waveguide lightmode spectroscopy. Biomacromolecules, 8(3), 963-970.
https://doi.org/10.1021/bm060293+
Collecte d'extraits volatils HS-SPME réalisée dans une seringue à gaz en verre d'un volume de 100 ml placée sur un pousse-seringue polyvalent LAMBDA VIT-FIT
Poinot, P., Grua-Priol, J., Arvisenet, G., Rannou, C., Semenou, M., Le Bail, A., & Prost, C. (2007). Optimisation of HS-SPME to study representativeness of partially baked bread odorant extracts. Food Research International, 40(9), 1170-1184.
https://doi.org/10.1016/j.foodres.2007.06.011
2006
Le débit d’une solution tampon à travers une cellule de dépôt a été maintenu constant à 2 ml/h (correspondant à un temps de séjour d'environ 30 s) par le pousse-seringue programmable LAMBDA VIT-FIT. Le pousse-seringue permet une injection régulière de l’échantillon sans pulsation du débit, ce qui est particulièrement important pour les mesures de température.
Kroslak, M. (2006). Investigation of deposition and adsorption on solid-liquid interfaces through optical waveguide lightmode spectroscopy (Doctoral dissertation, ETH Zurich).
https://doi.org/10.3929/ethz-a-005244118
Expériences de dépôt dans OWLS 110 : Le débit a été maintenu constant à 1 ml/min par le pousse-seringue programmable LAMBDA VIT-FIT, qui fournit une injection régulière avec des pulsations de débit fortement réduites.
Kroslak, M. (2006). Investigation of deposition and adsorption on solid-liquid interfaces through optical waveguide lightmode spectroscopy (Doctoral dissertation, ETH Zurich).
https://doi.org/10.3929/ethz-a-005244118
Réactions semi-batch avec ajout de monomère (styrène (STY), méthacrylate de méthyle (MMA) ou acrylate de tert-butyle (BA)) à débit constant à l'aide du pousse-seringue LAMBDA VIT-FIT. (L'ajout par le pousse-seringue a commencé en même temps que l'ajout de l'initiateur.)
Apostolovic, B., Quattrini, F., Butté, A., Storti, G., & Morbidelli, M. (2006). Ab initio emulsion polymerization by RAFT (reversible addition–fragmentation chain transfer) through the addition of cyclodextrins. Helvetica chimica acta, 89(8), 1641-1659.
https://doi.org/10.1002/hlca.200690163
2005
Le dispositif expérimental se compose de deux générateurs de fonctions, de microseringues utilisées avec un LAMBDA VIT-FIT, d'un stéréomicroscope (Leica) et d’un processeur cellulaire intégré.
Park, J., Jung, S. H., Kim, Y. H., Kim, B., Lee, S. K., & Park, J. O. (2005). Design and fabrication of an integrated cell processor for single embryo cell manipulation. Lab on a Chip, 5(1), 91-96.
https://doi.org/10.1039/B404990J
Contrôle précis d'un tampon et d'un flux de particules dans un micro dispositif à l'aide d'un pousse-seringue LAMBDA VIT-FIT
Park, J., Kim, B., Choi, S. K., Hong, S., Lee, S. H., & Lee, K. I. (2005). An efficient cell separation system using 3D-asymmetric microelectrodes. Lab on a Chip, 5(11), 1264-1270.
https://doi.org/10.1039/B506803G
Injection d'une solution d'Al(NO3)3 dans le coagulateur par un pousse-seringue LAMBDA VIT-FIT réglé à la vitesse maximale, ce qui correspond à un temps d'injection d'environ 15 s
Waldner, M. H., Sefcik, J., Soos, M., & Morbidelli, M. (2005). Initial growth kinetics and structure of colloidal aggregates in a turbulent coagulator. Powder technology, 156(2-3), 226-234.
https://doi.org/10.1016/j.powtec.2005.04.014
2004
Système intégré de cellules biologiques utilisant des pousse-seringues LAMBDA VIT-FIT
Park, J. Y., Jung, S. H., Kim, Y. H., Kim, B. K., Lee, S. K., & Ju, B. K. (2004). An Integrated Cell Processor for Single Embryo Manipulation. KIEE International Transactions on Electrophysics and Applications, 4(5), 241-246.
https://koreascience.kr/article/JAKO200413842102771.pdf (2024 April 23)
Débit de gouttes en suspension contrôlé par un pousse-seringue LAMBDA VIT-FIT
Kim, Y. H., Hong, S., Kim, B., Yun, S., Kang, Y. R., Paek, K. K., Lee, J.W., Lee, S.H., & Ju, B. K. (2004, September). Droplet-based magnetically activated cell separation. In The 26th Annual International Conference of the IEEE Engineering in Medicine and Biology Society (Vol. 1, pp. 2575-2578). IEEE.
https://doi.org/10.1109/iembs.2004.1403740
2003
Micro-pousse-seringue LAMBDA VIT-FIT avec fonction de perfusion et de refoulement utilisé pour contrôler l'orientation de l'œuf de poisson zèbre en modifiant le débit dans un micro-canal
Namkung, Y. W., Park, J. Y., Kim, B. K., Park, J. O., & Kim, J. O. (2003). Microfluidic Control for Biological Cell Orientation. 제어로봇시스템학회: 학술대회논문집, 2457-2460.
https://koreascience.kr/article/CFKO200333239337684.pdf (2024 April 22)